PROJECTA 12V 30A Charger & 35A Power Supply 30A Solar controller
R12,369.57 (Incl. Vat)
SKU: PM200
PM 200’s remote display features 3 water levels, starter and service battery voltages, switch for water pump control, night mode buttons and load on/off switch.
In stock
| Range | Discount |
|---|---|
| 0 - 4 | 0% |
| 5 - 9 | 3% |
| 10 - 20 | 6% |
| 20 + | 0.5% |
PM 200’s remote display features 3 water levels, starter and service battery voltages, switch for water pump control, night mode buttons and load on/off switch. The 30A PWM solar input allows the user to rely on solar during sunny conditions or DC when it’s not. WAGO terminals make installation and changes to wiring a breeze, whilst a manual battery switch connection allows for remote or local operation.
Technical Specs
| ELECTRICAL | |
| Grid | |
| Nominal input voltage (V) | 240±10%VAC 50/60Hz |
| Power factor | 0.95 |
| Input current at full load | 2.5A |
| Battery | |
| Starter battery | 12VDC |
| Starter battery voltage range | 12.8-16VDC |
| Service battery | 12VDC |
| Service battery voltage range | 10.5-16VDC |
| PV | |
| Charger type | PWM |
| Open circuit voltage | 25VDC |
| Max supply current | 30A |
| Max charging current | 30A |
| Charging Relay | |
| Relay Specification | 12VDC 60A continuous, peak current 100A, 30mins |
| Connect voltage | Lead Acid – 13.4VDC |
| LiFePO4 – 14.0VDC | |
| Connect delay time | 10 sec |
| Disconnect voltage | Lead Acid – 12.8VDC |
| LiFePO4 – 13.5VDC <2A | |
| Disconnect delay time | 60 sec |
| High voltage limit | 16.0VDC |
| Charger mode | |
| Charge Algorithms | 5 Stage |
| Battery type | AGM/GEL/LiFePO4/WET |
| Start voltage | 2V |
| Bulk current | 30A (Max) |
| Absorption voltage | (14.4/14.1/14.4/14.7) ±0.15VDC |
| Float Voltage | (13.5/13.5 /13.5/13.7) ±0.13VDC |
| Power supply mode | |
| Nominal output voltage | 12.8±0.2 VDC |
| Rated output current | 35A (Continuous) |
| Efficiency | 88% |
| Working temperature | -40°C~+65°C (50°C: full load; 60°C: 20A; 65°C: shutdown the output) |
| OTHER | |
| Battery Disconnect (LVD) | |
| Disconnect voltage | 10.5VDC (default) AGM/GEL/WET |
| 11.2 VDC (Default) LiFePO4 | |
| Delay off time | 60 sec |
| Reconnect voltage | 11.5VDC (default) AGM/GEL/WET |
| 12.2 VDC (Default) LiFePO4 | |
| Current Draw on Battery | |
| 240VAC is off, no vehicle charging | 405mA |
| LVD battery <10.5V. Current draw on battery | 110mA |
| LVD battery <10.0V. Current draw on battery | 0mA |
| Fused outputs | |
| Numbers | 14 |
| Rated current | 15A x 4: 10A x 10 |
| Protection | |
| Short circuit on output | Fuse blown |
| Reverse Polarity | Diode reverse isolation |
| Overload protection | Derate the output until overload is removed |
| Battery charger over temperature | shutdown PM200 |
| Ambient over temperature | Alarm |
| Battery over voltage limits | Battery charger disconnect, loads disconnect |
| PHYSICAL | |
| Dimensions (L*W*H) | 264x164x128mm |
| Weight (kg) | 3kgs |
| Enclosure | Steel case |
| Protection category | IP20 |
| APPROVALS | |
| Electrical | AS/NZS 60335-2-29 |
| EMC | CISPR14 |
Features
• Smart battery charger 12V 35A (30A for charging current)
• Float charge for starter battery
• Solar charge controller (PWM), 30A
• 14 built-in outputs
• Charging from Alternator at 12V 60A – 60A continuously, 100A 30mins
• Battery Low Voltage Protection
• Built-in battery switch to isolate the battery when in storage
• Support external remote battery switch
• Built-in shunt for precise battery measurement
• 1 water pump control with up to 3 connections for water sensors
• Thermal controlled fan
• Spring terminal & screw terminal
• T-bus compatible
Warranty
2-Years
Related products
Power Management
Power Management
Power Management
Power Management
PROJECTA 12V 30A Charger & 35A Power Supply, 30A MPPT Solar Controller, Dimmable Lights BT
Power Management
Power Management
Power Management
PROJECTA 12V 30A Charger & 35A Power Supply, 30A MPPT Solar Controller, Dimmable Lights
Power Management